Welcome Aboard!

10% savings across all ranges sitewide for new customers · Terms apply

FLASHSALE26

Johnson 8HP 2-Stroke Outboard Marine Engine Parts

(36 products)

This page is dedicated to Johnson 2‑Stroke 8HP outboard engines. Use it to find compatible replacement parts and service information. Below you’ll find maintenance tips, common replacement part categories, and quick troubleshooting guidance. You can also browse the main Johnson/Evinrude collection. Scroll to the bottom of this page to start browsing parts for this engine, and remember you can use the “Filter & Sort” controls on the collection page to narrow results by horsepower, year range, and part category.

Browse All Johnson/Evinrude Parts

How to Identify Your 8HP Model

  • Locate the nameplate/serial plate: typically on the transom bracket (mounting clamp area) or on the swivel bracket just below the engine cover.
  • Read the full model code and serial number: suffix letters often indicate shaft length (e.g., S = short 15”, L = long 20”) and starter/control options (manual vs. electric start).
  • Confirm stroke and platform: Johnson 8HP in this range is a 2‑Stroke, twin‑cylinder, carbureted outboard. Knowing this helps match ignition, fuel, and cooling parts.
  • Note year identifiers: small variations by year can affect ignition components, carb kits, and water pump parts—verify using the exact model code.

Engine Overview

Johnson 8HP 2‑Stroke Platform

Feature Description
Configuration Inline‑2, carbureted 2‑Stroke with CDI ignition; manual or electric start depending on model; typical 15" or 20" shaft options.
Common Models Johnson 8HP 2‑Stroke variants across multiple years; confirm exact model code for parts fit.
Advantages Light weight, simple service, easy starting, reliable trolling performance.
Notes Many routine items (spark plugs, anodes, impellers) are shared with similar‑era Johnson/Evinrude small twins, but always verify by model number and shaft length.

Routine Maintenance & Service Parts

Intervals below are general guidelines; always follow your official service manual and the decals on your engine. For small Johnson 2‑Stroke engines, most run a 50:1 fuel/oil premix unless otherwise specified on the engine cover.

Item Interval* Remarks Parts Link
Gear oil (lower unit) Every 100 hours or annually Inspect drain/fill screw gaskets; check for water or metal particles. Replace seals if contamination is found. Johnson/Evinrude Collection
Spark plugs Inspect every 50 hours; replace 100 hours/annually Use correct heat range and gap; fouling indicates mixture or ignition issues. Spark Plugs
Fuel filter / water separator Inspect every 50 hours; replace as needed Keep fuel clean to prevent carburetor issues; replace clogged filters promptly. Fuel Filters
Water pump impeller / kit Every 2–3 seasons (more often in sandy/silty water) A strong tell‑tale stream is critical; replace if weak flow or overheating occurs. Johnson/Evinrude Water Pump Kits
Impeller (replacement only) Inspect annually; replace as needed Carry a spare impeller for remote trips. Johnson/Evinrude Impellers
Anodes (zincs) Inspect every 50 hours; replace when 50% depleted Choose material for your water (aluminum, magnesium, or zinc). Johnson/Evinrude Anodes
Lower unit seals (if leak suspected) Inspect at each gear‑oil change Milky oil indicates water intrusion; reseal before further use. Lower Unit Seal Kits

*Intervals are typical for recreational use; shorten for heavy or commercial operation.

Frequently Used Parts Categories

Common Symptoms & Quick Checks

Symptom Check First Related Parts
Weak tell‑tale stream or overheat alarm Inspect intake screen for debris; verify impeller age; ensure thermostat passage is clear. Water pump kit, impeller, intake screen, thermostat components
Hard starting / rough idle Confirm fresh 50:1 premix; check spark plug condition/gap; look for stale fuel or clogged filter. Spark plugs, fuel filter, fuel pump, carb service items
Poor acceleration / power loss Inspect propeller for damage; check compression; verify clean carburetor and fuel flow. Propeller, fuel filter/pump, ignition items, carb kits
Excessive smoke Verify correct fuel/oil ratio; ensure plugs aren’t fouled; check for prolonged idling or rich mixture. Spark plugs, fuel system components
Gearcase noise or metal in gear oil Check gear oil condition; inspect for water intrusion; evaluate prop shaft and seals. Lower unit seal kit, prop hardware, bearings

FAQs

Are parts interchangeable across different years or similar small Johnson models?

Many wear items are similar across small Johnson/Evinrude twins of the same era, but ignition, carburetor, and water pump details can differ. Always match parts using your exact model code and serial number.

When should I replace the water pump impeller?

As a rule of thumb, every 2–3 seasons or sooner if you run in sandy/silty water, see a weak tell‑tale stream, or encounter an overheat alarm. Complete pump kits are a best practice during major services.

How often should I change lower unit gear oil?

Change it at least annually or every 100 hours. Inspect for water (milky appearance) or metal particles. If contamination is found, diagnose and reseal before further use.

What information do you need to confirm part compatibility?

Provide the full model code, serial number, shaft length (S/L), starting method (manual/electric), and any known year range. Photos of the nameplate and the existing part are also helpful.

Ready to find the parts you need? Browse the main Johnson/Evinrude collection and use the filters to narrow by horsepower, year, and category.

Shop Johnson/Evinrude Parts

If you’re unsure about your model, send us a photo of the nameplate and the part you need and we’ll help verify compatibility.
View as
Back to top

Compare /5