Evinrude 58HP 2-Stroke Outboard Marine Parts

(0 products)

This page focuses on Evinrude 2‑Stroke 58HP outboard engines. Use it to find compatible parts and practical service information, including maintenance tips, frequently replaced components, and troubleshooting guidance. You can also browse the main Evinrude/Johnson collection, and at the bottom of this page you’ll find a quick link to start browsing parts for this engine. On the collection page, use the Filter & Sort controls to narrow results by horsepower, year range, and part category/section.

Browse All Evinrude Parts

How to Identify Your 58HP Model

Find the model/serial plate on the clamp bracket or near the top of the swivel bracket. Clean the area so the code is fully legible.
Decode the model string: letters often indicate shaft length (S/L/XL), starting/controls (e.g., E for electric start, R for remote), and a year suffix. Match these details before ordering.
Confirm platform details: many 58HP units are carbureted 2‑strokes. Cylinder count (2 vs 3) can be verified by the number of spark plug leads and the block casting.
Oil system check: determine if your engine is premix or uses oil injection (VRO). This affects fuel and oil hose routing and related service parts.

Platform Overview

Inline‑3 Carbureted 2‑Stroke (common on later midrange models)

Feature	Description
Configuration	Inline‑3, carbureted 2‑stroke with mechanical fuel system.
Common Models	58HP and related midrange Evinrude/Johnson variants in the 55–70HP family.
Advantages	Smooth running for its size, strong mid‑range torque, broad parts availability.
Notes	Many components cross over with 60–70HP siblings; verify jetting, gearcase style, and model suffix for exact fit.

Inline‑2 Carbureted 2‑Stroke (seen on earlier 55/60HP family)

Feature	Description
Configuration	Inline‑2, carbureted 2‑stroke with simple ignition and fuel systems.
Common Models	Earlier 55–60HP variants that share many service parts with 58HP‑rated units.
Advantages	Lightweight and easy to service; robust cooling and gearcase design.
Notes	Ignition modules, carb sizes, and gear ratios can differ by year; use the exact model number to confirm compatibility.

Routine Maintenance & Service Parts

Intervals below are general guidelines for Evinrude 2‑stroke midrange outboards. Always confirm procedures and intervals with your official service manual.

Item	Interval*	Remarks	Parts Link
Gear oil (lower unit)	Every 100 hrs or annually	Change before winter; inspect for water intrusion (milky oil). Reseal if contamination recurs.	Johnson/Evinrude Parts
Spark plugs	Inspect every 100 hrs; replace as needed	Use correct heat range and gap; replace if fouled, worn, or cracked.	Spark Plugs
Fuel filter / in‑line filter	Every 100 hrs or annually	Replace more often with ethanol fuel or contaminated tanks; verify hose condition.	Fuel Filters
Water pump impeller / kit	200 hrs or 2–3 seasons	Critical for cooling; replace sooner if weak tell‑tale or overheat events occur.	Water Pump Repair Kits
Anodes (sacrificial zinc/aluminum)	Inspect every 50 hrs; replace at ~50% wear	Choose alloy for your water (salt, brackish, fresh). Keep electrical bonding intact.	Johnson/Evinrude Anodes
2‑Stroke oiling (premix or injection)	Each fill‑up / seasonal check	Verify premix ratio or test VRO operation; inspect oil and fuel hoses for softness/cracking.	Fuel & Oil Hoses
Propeller & hardware	Inspect regularly	Check for dings and spun hubs; grease splines; verify cotter/locking tabs.	Johnson/Evinrude Propellers

Frequently Used Parts Categories

Routine Service Kits – Johnson/Evinrude Service & Maintenance Kits
Cooling System – Water Pump Repair Kits
Propellers & Hubs – Johnson/Evinrude Propellers
Corrosion Protection – Anodes
Fuel System – Fuel Filters and Hoses
Ignition / Electrical – Electrical Items and Starters
Gearcase & Sealing – Lower Unit Seal Kits

Common Symptoms & Quick Checks

Symptom	Check First	Related Parts
Weak tell‑tale stream / overheat alarm	Inspect intake screens for debris, verify hose routing, test impeller output, and confirm thermostat operation.	Water pump kit, intake screen, thermostat, hoses
Hard starting / rough idle	Prime fuel system, check for stale fuel, verify choke/primer function, inspect plugs and idle mixture.	Spark plugs, fuel filter, carburetor kit, primer/choke components, hoses
Poor acceleration / power loss	Check prop damage/slip, compression, timing advance, and fuel restriction; look for exhaust leaks at the powerhead base.	Propeller, spark plugs, fuel filter, fuel pump diaphragm, gaskets
Excessive smoke (2‑stroke)	Verify premix ratio or VRO operation; ensure choke isn’t stuck; check thermostat closing temp.	Oil pump/VRO components, choke solenoid, thermostat
Gearcase noise / metal in gear oil	Check oil level/condition, inspect prop shaft for fishing line, test for water intrusion; consider reseal.	Lower unit seal kit, gear lube, prop shaft seals

FAQs

Are parts interchangeable between different 58HP years or platforms?

Many items (anodes, pumps, some ignition and gearcase parts) overlap with the broader 55–70HP family, but jetting, ignition modules, and gear ratios vary by year and platform (inline‑2 vs inline‑3). Always match by the exact model number and suffix to confirm fit.

When should I replace the impeller?

As a rule of thumb, every 2–3 seasons or ~200 hours. Replace sooner if operating in sandy, silty, or weedy water, or if you notice a weak tell‑tale stream or any overheat alarms.

How often should gear oil be changed?

Change every 100 hours or at least annually, and always before winter storage. If oil appears milky or contaminated, investigate for water intrusion and consider a reseal.

What information do you need to confirm compatibility?

Provide the full model number and serial, horsepower rating, shaft length, starting/controls (tiller/remote, manual/electric), and any photos of the nameplate and the parts you’re replacing.

Ready to find parts by horsepower, year, and model? Browse the main Evinrude/Johnson collection to zero in on components that fit your specific 58HP outboard.

Start Browsing Parts

If you’re unsure about your model, send us a clear photo of the nameplate and the part you need and we’ll help verify compatibility.