Honda Marine 200HP 4-Stroke Outboard Engine Parts

(21 products)

This page focuses on Honda 4‑Stroke 200HP outboard engines and helps you find compatible parts and service information. Below you’ll find maintenance tips, common replacement parts, and troubleshooting guidance. You can also browse our main Honda collection, and at the bottom of this page you can start browsing parts for this engine. On the collection pages, use the “Filter & Sort” controls to narrow results by horsepower, year range, and part category.

Browse All Honda Parts

How to Identify Your 200HP Model

Find the serial/name plate: typically stamped on the right side stern bracket; the engine serial number is stamped on the upper right side of the powerhead frame.
Model codes: common 200HP 4‑stroke models are BF200A variants. Suffixes indicate shaft length and rotation (e.g., LA/XA/XXA = 20/25/30 in; XCA/XXCA = counter‑rotating).
4‑Stroke indicators: presence of an engine oil dipstick and filler cap under the cover; EFI system indicators and sensors (PGM‑FI) are typical on BF200A.
Controls and rigging: remote control types (side, panel, top‑mount) and trim/tilt switch placement help confirm configuration noted on the serial plate.

Engine/Platform Overview

Honda BF200A (V6 EFI 4‑Stroke)

Feature	Description
Configuration	3.5L class SOHC V6, EFI, power trim/tilt, 12V charging (high‑output alternator)
Common Models	BF200A LA / XA / XXA (20/25/30 in); BF200A XCA / XXCA (counter‑rotating)
Advantages	Smooth V6 power delivery, strong mid‑range torque, efficient EFI fueling, robust corrosion protection (multiple anodes)
Notes	Many routine‑service parts overlap with BF225A, but always confirm by model code and serial. Check rotation (standard vs. counter) and shaft length when ordering props and gearcase components.

Routine Maintenance & Service Parts

Intervals below are general guidelines. Always follow the official Honda service manual for your exact model and usage.

Item	Interval*	Remarks	Parts Link
Engine oil + filter	Every 100 hrs or 6 months	Use marine‑rated oil; warm engine before draining; replace crush washer	Oil Filters
Gear oil (lower unit)	Every 100 hrs or annually	Inspect magnet/drain plug for metal; replace seals if leakage is found	Honda Outboard Parts
Spark plugs	Inspect 100 hrs; replace ~200 hrs	Use the specified heat‑range; check condition and gap	Spark Plugs
Fuel filter / water separator	Check 100 hrs; replace ~200 hrs	Drain/clean if water is present; replace if contaminated	Fuel Filters
Water pump impeller / kit	Every 200 hrs or 2 seasons	Replace sooner for sandy/turbid use or weak tell‑tale stream	Honda Water Pump Repair Kits
Anodes (gearcase/bracket/block)	Inspect often; replace when ~50% eroded	Do not paint or coat; verify secure fasteners	Anodes
Thermostat (inspection/replacement)	~Every 2 years or 400 hrs	Replace if overheat or slow warm‑up persists	Honda Outboard Parts
Lower unit seal kit (if water intrusion)	As needed	Use pressure/vacuum test to confirm seal integrity	Honda Lower Unit Seal Kits

*Intervals are general guidelines and may vary by usage (saltwater, trolling, storage). Always follow the official service manual.

Frequently Used Parts Categories

Routine Service: Service & Maintenance Kits
Cooling System: Honda Water Pump Repair Kits
Fuel System: Fuel Filters and Fuel Pumps
Ignition / Electrical: Electrical Items and Spark Plugs
Corrosion Protection: Anodes
Propulsion & Driveline: Propellers and Lower Unit Seal Kits
Accessories: Boat Accessories

Common Symptoms & Quick Checks

Symptom	Check First	Related Parts
Weak tell‑tale stream / overheat alarm	Inspect intake screens for debris; verify pump output; confirm thermostat function	Water pump kit, thermostat, intake screen
Poor acceleration or power loss	Check fuel quality, water in separator, clogged fuel filter, fouled propeller	Fuel filter, water separator, spark plugs, propeller
Hard starting / rough idle	Prime fuel line; verify battery and emergency stop switch; inspect plugs	Spark plugs, fuel filter, battery, ignition components
Gearcase noise or milky gear oil	Drain and inspect gear oil; check for water; test seals	Gear oil, lower unit seal kit, bearings

FAQs

Are parts interchangeable across different years or between BF200A and BF225A?

Many routine service items are shared across these V6 platforms, but variations by year, shaft length, and rotation exist. Always confirm with your full model code (e.g., BF200A XA) and serial number before ordering.

When should I replace the water pump impeller?

As a rule of thumb, replace every 200 hours or 2 seasons—earlier if operating in sand, silt, or if the tell‑tale weakens or the engine overheats.

How often should I change the gear oil?

Change at least annually or every 100 hours. Inspect for metal and water contamination; service seals if you detect leakage.

What information do you need to verify part compatibility?

Provide the model code and serial number from the nameplate, shaft length (20/25/30 in), rotation (standard or counter), control type, and any known year range. Photos of the nameplate and the part can also help.

Ready to find parts for your Honda 200HP outboard? Browse the main Honda collection and use the filters by horsepower, year, and part category.

Shop Honda Outboard Parts

If you’re unsure about your model, send us a photo of the nameplate and the part you need and we’ll help verify compatibility.