Honda Marine 250HP 4-Stroke Outboard Engine Parts

(13 products)

This page is dedicated to Honda Marine 4-Stroke 250 HP outboard engines. Use it to find compatible parts, routine service information, maintenance tips, frequently used categories, and troubleshooting guidance. You can also browse our main Honda collection any time. Scroll to the bottom of this page to start browsing parts for this engine, and remember you can use the Filter & Sort controls on the collection page to narrow results by horsepower, year range, and part category.

Browse All Honda Parts

How to Identify Your 250 HP Model

Find the model/serial plate on the transom bracket (port side) or swivel bracket. It shows the model code (e.g., BF250A or BF250D) and a serial range.
Model suffixes indicate shaft length and control/rigging (e.g., L/X/XX for 20/25/30-inch, remote vs. tiller), and sometimes rotation (standard vs. counter-rotation).
Honda 250 HP four-strokes are V6 EFI platforms; newer “D” designations supersede earlier “A” models. Confirm your exact model and serial to ensure parts fit.
When in doubt, take a clear photo of the nameplate and note rotation (standard or counter), shaft length, and control type.

Platform Overview

BF250A (First Generation)

Feature	Description
Configuration	60° V6, EFI 4‑stroke outboard
Common Models	BF250A (standard rotation and counter-rotation variants)
Advantages	Strong torque, good fuel economy for class, robust charging output
Notes	Confirm shaft length and rotation when selecting gearcase, water pump, and propeller parts.

BF250D (Later Generation)

Feature	Description
Configuration	60° V6, EFI 4‑stroke outboard (updated platform)
Common Models	BF250D and BF250DK1 (standard and counter-rotation)
Advantages	Refinements in calibration and durability; broad parts availability
Notes	Many wear items are similar across A/D platforms, but verify by model code and serial for exact fit.

Routine Maintenance & Service Parts

Intervals below are general guidelines for Honda four-stroke outboards. Always follow the official service manual for your exact model and usage.

Item	Interval*	Remarks	Parts Link
Engine oil & filter	Every 100 hours or annually	Use marine-rated oil; replace filter with each oil change	Oil Filters
Gear oil (lower unit)	Every 100 hours or annually	Inspect for water intrusion/metal; renew drain/vent gaskets	Honda Lower Unit Seal Kits
Spark plugs	Inspect 100 hours; replace 300 hours or as needed	Check gap and condition; replace sooner for heavy trolling	Spark Plugs
Fuel filter / water-separating filter	100–200 hours or annually	Replace more frequently in ethanol or contaminated fuel environments	Fuel Filters
Water pump impeller/kit	Every 200 hours or 2–3 seasons	Replace sooner for sand/silt use or weak tell‑tale stream	Honda Water Pump Repair Kits
Anodes (external & internal)	Inspect every 50 hours; replace when 50% depleted	Use correct alloy for fresh, brackish, or salt water	Anodes

*Intervals vary by operating hours, load, and environment. Always follow the maintenance schedule for your specific model.

Frequently Used Parts Categories

Routine Service: Service & Maintenance Kits
Cooling System: Honda Water Pump Repair Kits
Gearcase & Seals: Honda Lower Unit Seal Kits
Fuel System: Fuel Filters & Fuel Pumps
Ignition / Electrical: Electrical Items & Starters
Propulsion: Propellers
Corrosion Protection: Anodes

Common Symptoms & Quick Checks

Symptom	Check First	Related Parts
Weak tell‑tale stream or overheat alarm	Inspect intake screens, thermostat, and impeller condition	Water pump kit, thermostat, intake screen
Poor acceleration or power loss	Check prop pitch/condition, fuel quality, and filters; scan for codes if available	Propeller, fuel filter, spark plugs, fuel pump
Hard starting or rough idle	Verify battery voltage, plug condition, and stale fuel; inspect air/fuel filters	Spark plugs, fuel filter, electrical items (battery cables/relays)
Gearcase noise or metal in gear oil	Check oil level and water intrusion; inspect prop shaft seals	Lower unit seal kit, gear oil drain/vent gaskets, prop shaft hardware

FAQs

Are parts interchangeable between BF250A and BF250D?

Some wear items cross over, but many components (electronics, gearcase details, rigging) differ. Always confirm by full model code and serial number before ordering.

When should I replace the water pump impeller?

As a rule of thumb every 200 hours or 2–3 seasons, sooner if you operate in sandy/silty water or see a weak tell‑tale stream.

How often should I change gear oil?

Typically every 100 hours or annually. Inspect for water contamination or metal; if present, service seals before returning to use.

What information do you need to confirm part compatibility?

Please provide the full model code (e.g., BF250A/BF250D), serial number, shaft length, rotation (standard or counter), and control type. A photo of the nameplate helps ensure an exact match.

Ready to find parts for your Honda 250 HP? Browse the main Honda collection and use Filter & Sort to narrow by horsepower, year, and model.

Shop Honda Outboard Parts

If you’re unsure about your model, send us a photo of the nameplate and the part you need and we’ll help verify compatibility.