Johnson 2HP 2-Stroke Outboard Marine Engine Parts

(6 products)

For Johnson 2‑Stroke 2 HP outboard engines, this page helps you find compatible parts and service information. Below you’ll find maintenance tips, frequently used replacement parts, and troubleshooting guidance. You can also browse our main Johnson/Evinrude collection. Scroll to the bottom of the page to start browsing parts for this engine, and remember: on the collection page you can use the Filter & Sort controls to narrow results by horsepower, year range, and part category/section.

Browse All Johnson Parts

How to Identify Your 2 HP Model

Model/serial tag location: look on the top outside edge of the clamp bracket or on the top of the swivel bracket (port or starboard).
Reading the model code: the base model identifies horsepower; suffix letters/numbers often indicate year, shaft length (short/long), and starting/control configuration. Verify these to ensure parts match.
2‑Stroke identification: most Johnson 2 HP engines are compact, rope‑start, tiller‑steer, carbureted two‑strokes. Later 1990s models may have minor ignition and cover updates—confirm by model year.

Engine Overview

Johnson 2 HP 2‑Stroke

Feature	Description
Configuration	Single‑cylinder, carbureted 2‑stroke, rope‑start, water‑cooled, tiller steer.
Common Models	Johnson 2 HP 2‑Stroke models across approximately 1971–1985 and 1993–1997 (confirm exact model/year for parts).
Advantages	Very light and portable, simple maintenance, easy starting, and shallow‑water friendly.
Notes	Some parts vary by year or revision (water pump, gearcase seals, ignition). Always match by model/serial details before ordering.

Routine Maintenance & Service Parts

Intervals below are general guidelines—always follow the procedures and schedules in your official service manual.

Item	Interval*	Remarks	Parts Link
2‑Stroke fuel/oil mix	Every refuel	Many Johnson 2 HP models run 50:1 TC‑W3 outboard oil—verify the exact ratio/spec in your manual.	Johnson/Evinrude Collection
Spark plugs	Inspect 50 hrs; replace annually	Check heat range and gap per model/year. Replace if fouled or worn.	Spark Plugs
Inline fuel filter	Inspect 50 hrs; replace as needed	Replace if restricted or contaminated. Use quality fuel and stabilize for storage.	Fuel Filters
Water pump impeller/kit	Inspect annually; replace 2–3 seasons	Replace sooner if tell‑tale is weak, engine overheats, or after sandy/silty use.	Johnson/Evinrude Water Pump Kits
Gear oil (lower unit)	Every season or 100 hrs	Inspect for water (milky oil). Replace drain/vent gaskets; service seals if contamination is found.	Johnson/Evinrude Collection
Anodes (zincs)	Inspect each season	Replace when 50% consumed. Match alloy (zinc/aluminum/magnesium) to water type.	Johnson/Evinrude Anodes
Propeller & shear pin	Inspect every outing	Check for dings, bent blades, and a damaged shear pin. A clean prop restores thrust on small HP engines.	Johnson/Evinrude Propellers

Frequently Used Parts Categories

Routine Service Kits – Johnson/Evinrude Service & Maintenance Kits
Cooling System – Water Pump Repair Kits
Lower Unit Seals – Seal Kits
Propellers & Shear Pins – Propellers
Ignition & Spark – Spark Plugs
Fuel System – Fuel Filters
Carburetion – Carburetors & Components

Common Symptoms & Quick Checks

Symptom	Check First	Related Parts
Weak tell‑tale or overheat	Clear intake screen; verify tell‑tale passage; inspect impeller condition and key.	Water pump kit, intake screen, grommets, thermostat (if equipped).
Hard starting / rough idle	Use fresh fuel; verify choke/primer; inspect spark plug and plug gap; check for air leaks in fuel line.	Spark plug, inline fuel filter, carburetor kit, primer bulb/lines.
Poor acceleration / low power	Inspect prop for damage or wrong pitch; check for fouled plug; ensure throttle opens fully; clean carb jets.	Propeller, spark plug, carb jets/gaskets, fuel filter.
Excessive smoke	Verify oil mix ratio; avoid prolonged idling; check choke not stuck closed.	Correct TC‑W3 oil at proper ratio, spark plug, carb adjustments.
Gearcase noise or milky gear oil	Drain/fill gear oil; inspect for water; check prop shaft for fishing line and seal damage.	Lower unit seal kit, drain/vent gaskets, gear lube.

FAQs

Are parts interchangeable between different 2 HP years?

Some components interchange, but many items—especially water pump parts, gaskets, ignition pieces, and gearcase seals—can vary by year and revision. Always verify by model and serial before ordering.

When should I replace the impeller?

Inspect annually and replace every 2–3 seasons under normal use. Replace immediately if cooling flow is weak, the engine overheats, or after sand/silt exposure.

How often should I change the lower unit gear oil?

At least once per season or every 100 operating hours. If oil appears milky or contaminated, service seals and refill with fresh gear lube.

What information helps confirm part compatibility?

Provide the full model code, serial number, approximate year, shaft length, and starting/control type. Photos of the nameplate and the part you’re replacing are also helpful.

Ready to find parts by horsepower, year, and model? Browse our Johnson/Evinrude collection to zero in on components that fit your specific 2 HP outboard.

Shop Johnson/Evinrude Parts

If you’re unsure about your model, send us a photo of the nameplate and the part you need and we’ll help verify compatibility.