OMC 8HP 4-Stroke Outboard Marine Engine Parts

(2 products)

This page is dedicated to OMC 4‑Stroke 8HP outboard engines. Use it to find compatible parts and service information, including maintenance tips, common replacement items, and troubleshooting guidance. You can also browse our main Johnson/Evinrude/OMC collection. Scroll to the bottom of this page to start browsing parts for this engine, and on the collection page use the Filter & Sort controls to narrow results by horsepower, year range, and part category.

Browse All Johnson/Evinrude/OMC Parts

How to Identify Your 8HP Model

Nameplate location: look for the model/serial plate on the transom bracket or clamp bracket. The same ID is usually stamped on an under-cowl sticker.
Reading the model code: suffix characters often indicate shaft length (S/L/XL), starting/controls (manual vs. electric/remote), and a year or revision code.
Confirm 4‑Stroke: cowl decals and the presence of an engine oil fill/dipstick help distinguish 4‑Stroke from 2‑Stroke models.
Year range cue: many OMC 8HP 4‑Stroke portables were produced in the mid‑1990s to early‑2000s; verify exact year by the serial/model code.

Engine Overview

OMC 8HP 4‑Stroke Portable (approx. 1995–2004)

Feature	Description
Configuration	Inline‑2, carbureted 4‑Stroke portable outboard (around 211 cc), manual or electric start, short/long shaft variants.
Common Models	8 HP 4‑Stroke 211 cc family; many share cooling and gearcase components with certain 9.9 HP 211 cc models. Always verify by model code.
Advantages	Quiet operation, good fuel economy, simple routine service, portable form factor.
Notes	Water pump/gearcase parts are model‑year sensitive. Match by exact model and serial when ordering.

Routine Maintenance & Service Parts

Intervals below are general guidelines for typical recreational use. Always follow the official service manual for your specific model and operating conditions.

Item	Interval*	Remarks	Parts Link
Engine oil + filter	After 20 hours (break‑in), then every 100 hours or annually	Use marine 4‑Stroke oil of the correct viscosity; replace filter where equipped.	Johnson/Evinrude/OMC Service & Maintenance Kits
Gear oil (lower unit)	Every 100 hours or annually; also after water ingestion or submersion	Inspect drain/fill screws and seals; check for metal or milky oil.	Johnson/Evinrude/OMC Lower Unit Seal Kits
Spark plugs	Inspect every 100 hours; replace 200 hours or as needed	Set to spec; replace if fouled, worn, or corroded.	Spark Plugs
Fuel filter / water separator	Every 100 hours or annually; sooner with stale/contaminated fuel	Replace inline filter; consider a boat‑side separator for ethanol fuels.	Fuel Filters
Water pump impeller / kit	Every 2–3 seasons or 200 hours; inspect annually	Critical for cooling; replace sooner if stream weakens or after sand/silt use.	Johnson/Evinrude/OMC Water Pump Repair Kits
Anodes (zincs)	Inspect every 50 hours; replace when ~50% consumed	Choose alloy for your water (zinc/brackish, aluminum, or magnesium/fresh).	Johnson/Evinrude/OMC Anodes

Frequently Used Parts Categories

Routine Service – Johnson/Evinrude/OMC Service & Maintenance Kits
Cooling System – Johnson/Evinrude/OMC Water Pump Repair Kits
Lower Unit & Seals – Johnson/Evinrude/OMC Lower Unit Seal Kits
Corrosion Protection – Johnson/Evinrude/OMC Anodes
Propellers – Johnson/Evinrude/OMC Propellers
Ignition / Electrical – Electrical Items
Fuel System – Fuel Filters & Hoses

Common Symptoms & Quick Checks

Symptom	Check First	Related Parts
Weak tell‑tale or overheat alarm	Inspect intake screen for debris; verify strong tell‑tale; check impeller and thermostat.	Water pump repair kit, thermostat, gaskets, intake screen
Poor acceleration / power loss	Check prop for damage/cavitation; replace fuel filter; inspect plugs; confirm throttle linkages.	Propeller, fuel filter, spark plugs, fuel hose
Hard starting / rough idle	Use fresh fuel; verify choke/enricher operation; inspect plugs and idle mixture on carb models.	Spark plugs, fuel filter, carburetor parts
Gearcase noise / metal in gear oil	Drain and inspect gear oil; check for water intrusion; evaluate seals and bearings.	Lower unit seal kit, bearings, oil seals

FAQs

Are parts interchangeable between different years or related 8–9.9 HP models?

Some cooling and gearcase components are shared across the 211 cc 8–9.9 HP family, but there are year and model‑specific differences. Always confirm by model and serial before ordering.

When should I replace the water pump impeller?

Inspect annually and replace every 2–3 seasons or about 200 hours. Replace sooner if the tell‑tale weakens, if you ran in sand/silt, or after any overheat event.

How often should gear oil be changed?

Change every 100 hours or annually, and any time the oil appears milky (water contamination) or metallic. Renew crush washers/seals to prevent leaks.

What information do you need to confirm part compatibility?

Provide the full model code, serial number, shaft length (S/L/XL), start/controls type, and year if known. Photos of the nameplate and the part needing replacement are very helpful.

Ready to find parts by horsepower, year, and model? Browse the main Johnson/Evinrude/OMC collection and use Filter & Sort to narrow to your 8HP 4‑Stroke.

Shop Johnson/Evinrude/OMC Parts

If you’re unsure about your model, send us a photo of the nameplate and the part you need and we’ll help verify compatibility.