Parsun 4-Stroke 50HP Outboard Marine Engine Parts

(1 products)

This page is tailored for Parsun 4-Stroke 50HP outboard engines. It helps you find compatible parts and service information, including maintenance tips, commonly replaced items, and troubleshooting guidance. You can also browse our main collections for related components, and at the bottom of this page you’ll find quick links to start browsing parts for this engine. On the collection pages, use the “Filter & Sort” controls to narrow results by horsepower, year range, and part category/section.

Shop Service & Maintenance Kits

How to Identify Your 50HP Model

Locate the nameplate/serial plate on the transom bracket or swivel bracket. It typically lists model designation, serial number, and shaft length.
Model codes often start with “F50” for 4-stroke 50 hp. Suffix letters/numbers commonly indicate shaft length (S/L/XL), control type (tiller vs. remote), and tilt/trim options.
Parsun 4-strokes can be identified by the engine oil dipstick and oil fill under the top cowl. EFI models also include high-pressure fuel components.
The F50 often shares a platform with the F60 family; many hardware and service parts are similar, but verify by serial/model details before ordering.

Engine Overview

50HP Platform (Shared Family with 60HP)

Feature	Description
Configuration	Inline-4 EFI 4-stroke outboard with electronic fuel system and typical options for manual or power tilt/trim.
Common Models	Parsun F50 4-stroke variants (tiller or remote control; short/long/extra-long shaft where applicable). Often shares major service parts with F60 family models.
Advantages	Good fuel economy and low noise from EFI 4-stroke design; smooth mid‑range torque; broad parts availability for routine service.
Notes	Many cooling, anode, and gearcase service parts overlap across 50/60 hp family. Confirm with model/serial, shaft length, and control/tilt options before purchase.

Routine Maintenance & Service Parts

Intervals below are general guidelines for typical recreational use. Always follow the specific procedures and schedules in your official service manual.

Item	Interval*	Remarks	Parts Link
Engine oil + filter (4-stroke)	Every 100 hours or annually	Warm engine first; replace filter with each oil change. Dispose of used oil properly.	Oil Filters
Gear oil (lower unit)	Every 100 hours or annually	Inspect for metal shavings or water intrusion; replace seals if contamination is present.	Lower Unit Seal Kits
Spark plugs	Inspect every 100 hours; replace as needed	Check gap and color; replace if fouled, worn, or out of spec.	Spark Plugs
Fuel filter / water-separating filter	Every 100 hours or each season	Replace more often in ethanol-blend or contaminated fuel environments.	Fuel Filters
Water pump impeller / kit	Every 200 hours or 2 seasons	Shorten interval in sandy/silty or shallow operation; replace housing if scored.	Water Pump Impeller Kits
Anodes (internal/external)	Inspect every 50 hours; replace when 50% consumed	Match anode material to water type (salt, brackish, fresh) to maximize protection.	Anodes

*Intervals are typical recommendations; follow your specific model’s service schedule.

Frequently Used Parts Categories

Routine Service: Service & Maintenance Kits
Cooling System: Water Pump Impeller Kits
Fuel System: Fuel Filters and Fuel Pumps
Ignition / Electrical: Electrical Items and Starters
Propulsion: Propellers
Corrosion Protection: Anodes
Seals & Gaskets: Gaskets and Oil Seals

Common Symptoms & Quick Checks

Symptom	Check First	Related Parts
Weak telltale stream or overheat alarm	Inspect intake screens for blockage; verify impeller condition; check thermostat and passages.	Water pump impeller kit, thermostat, intake screen components, anodes.
Poor acceleration or power loss	Confirm clean fuel and filter; inspect spark plugs; verify prop pitch/condition and for cavitation.	Fuel filter, spark plugs, fuel pump/injectors, propeller.
Hard starting or rough idle	Check battery and connections; prime fuel system; inspect plugs; look for vacuum leaks.	Spark plugs, inline fuel filter, fuel pump, injectors, starter.
Gearcase noise or metal in gear oil	Drain and inspect gear oil; check for water intrusion; pressure/vacuum test and reseal if needed.	Lower unit seal kit, bearings, gear oil and drain/fill gaskets.

FAQs

Are parts interchangeable between 50HP and 60HP models?

Many hardware and routine service items are shared across the F50/F60 family (for example certain cooling, anode, and gearcase components). Electronic and calibration-related parts may differ. Always confirm by model code and serial number.

When should I replace the water pump impeller?

As a rule of thumb, replace every 200 hours or every 2 seasons, and sooner if you run in sandy/silty water or notice a weak telltale stream, overheat alarms, or impeller vane set.

How often should gear oil be changed?

Change at least every 100 hours or annually, and always before winter storage. If you find milky oil or metal shavings, address seals or internal wear before further operation.

What information helps confirm part compatibility?

Provide the full model designation, serial number, shaft length (S/L/XL), control type (tiller/remote), tilt/trim option, and clear photos of the nameplate and the part you are replacing.

Ready to maintain your Parsun 50HP? Browse parts by category and narrow by your engine’s details using the Filter & Sort tools on our collections.

Start with Service & Maintenance Kits

If you’re unsure about your model, send us a photo of the nameplate and the part you need and we’ll help verify compatibility.