Parsun 4-Stroke 6-8HP Outboard Marine Engine Parts

(1 products)

This page is dedicated to Parsun 4-Stroke 6–8HP outboard engines. Use it to find compatible parts and practical service information, including maintenance tips, common replacement items, and troubleshooting guidance. You can also browse our main Parsun parts collection. Scroll to the bottom of this page to start browsing parts for this engine, and remember you can use the Filter & Sort controls on the collection page to narrow results by horsepower, year range, and part category.

Browse All Parsun Parts

How to Identify Your 6–8HP Model

Nameplate location: Look on the transom bracket or clamp bracket for the model/serial plate; the serial may also be stamped on the swivel bracket.
Reading the code: Parsun small four-strokes often indicate horsepower (e.g., 6 or 8) plus shaft length (S = 153 short; L = 203 long) and start/control type (manual tiller is common).
4-stroke cues: Engine has a dipstick and oil fill cap; service intervals include engine oil and filter changes.
Platform distinctions: In this class, 6HP models are typically single-cylinder; some 8HP variants may be twin-cylinder depending on year. Count spark plugs (one vs two) and check displacement to verify.

Platform Overview

Parsun Small 4-Stroke 680HP

Feature	Description
Configuration	Carbureted OHV 4-stroke, CDI ignition, tiller-steer, manual start; integral small fuel tank with optional external tank on some models.
Common Models	6HP and 8HP 4-stroke outboards in short (S) and long (L) shaft variants; typical full-throttle range around 4,5005500 rpm for 6HP models.
Advantages	Quiet running, low fuel consumption, easy portability, and good trolling manners for dinghies, inflatables, and small skiffs.
Notes	Many wear items (plugs, impeller, anodes) are shared across nearby HP variants; confirm shaft length and gear ratio before propeller purchase. Always verify by model code and serial.

Routine Maintenance & Service Parts

Intervals below are general guidelines for small 4-stroke outboards. Always follow the official Parsun service manual for your exact model and operating conditions.

Item	Interval*	Remarks	Parts Link
Engine oil & filter	First 20 hrs; then every 100 hrs or annually	Warm engine before draining; replace crush washer if equipped; use marine 4T oil grade as specified.	Oil Filters
Gear oil (lower unit)	Every 100 hrs or annually	Change more often after submersion; inspect for water contamination (milky oil) and metal shavings.	Lower Unit Seal Kits
Spark plug(s)	Inspect 100 hrs; replace 200 hrs or as needed	Check gap and insulator color; replace if fouled or out of spec.	Spark plug
Fuel filter / inline filter	Every 100 hrs or annually	Replace sooner if debris or ethanol-related varnish is present; use fresh, stabilized fuel.	Fuel Filters
Water pump impeller / kit	Inspect annually; replace 2 seasons or 200 hrs	Replace sooner after dry-run, sand/silt ingestion, or weak tell-tale stream.	Water Pump Impeller Rebuild Kits
Anodes (internal & external)	Inspect often; replace when 50% consumed	Choose alloy for water type: zinc (salt), aluminum (salt/brackish), magnesium (fresh).	Anodes
Propeller inspection	Every 50100 hrs or at any vibration	Check for dings and bent blades; confirm pitch for load and altitude; use new cotter pin on install.	Propellers

*Intervals are typical for recreational use; shorten for commercial/heavy duty or harsh environments.

Frequently Used Parts Categories

Routine Service Service & Maintenance Kits
Cooling System Impellers
Fuel System Fuel Filters
Ignition / Electrical Electrical Items
Propulsion Propellers
Corrosion Protection Anodes
Gearcase Seals Lower Unit Seal Kits

Common Symptoms & Quick Checks

Symptom	Check First	Related Parts
Weak tell-tale stream or overheat alarm	Inspect intake screen for blockage; verify impeller condition; confirm thermostat operation.	Water pump impeller kit, thermostat, intake screen/grommets
Poor acceleration or power loss	Check fuel freshness and filter; inspect propeller for damage or wrong pitch; examine spark plug condition.	Fuel filter, propeller, spark plug
Hard starting or rough idle	Confirm choke/enrichment operation; look for vacuum leaks; clean carburetor jets if gummed.	Spark plug, fuel filter, carburetor parts
Gearcase noise or metal in gear oil	Drain and inspect gear oil; check for water intrusion through prop shaft or driveshaft seals; verify correct fill procedure.	Lower unit seal kit, bearings, shims

FAQs

Are parts interchangeable between different years or platforms?

Many wear items are shared across Parsun 68HP small four-strokes, but carburetion, ignition, and gearcase details can vary by year and shaft length. Always confirm by model code and serial before ordering.

When should I replace the impeller?

Inspect annually and replace about every two seasons or ~200 hours. Replace immediately if the motor was run dry, the tell-tale is weak, or you found sand/silt in the pump housing.

How often should I change the gear oil?

At least every 100 hours or once per year. If you see milky oil or metal flakes, service the lower unit seals and investigate for wear before running again.

What information helps confirm part compatibility?

Provide brand (Parsun), full model code, serial number, shaft length (S/L), and a photo of the nameplate. Pictures of the existing part also help us verify fitment.

Ready to shop? Browse our main Parsun-compatible parts by category and refine by horsepower, year, and model on the collection page.

Shop Parsun-Compatible Parts

If youre unsure about your model, send us a photo of the nameplate and the part you need and well help verify compatibility.