RECMAR 60HP 4-Stroke Marine Engine Parts

(0 products)

This page supports Mercury 4‑Stroke 60 HP outboard engines. Use it to find compatible parts and service information, including maintenance tips, frequently replaced items, and troubleshooting guidance. You can also browse the main Mercury collection. Scroll to the bottom of this page to start browsing parts for this engine, and on the collection page use the “Filter & Sort” controls to narrow results by horsepower, year range, and part category.

Browse All Mercury Parts

How to Identify Your 60 HP Model

Find the serial/nameplate on the starboard transom bracket or swivel bracket. It lists the model designation and serial number.
Read the model name and suffix: examples include “60 EFI FourStroke,” with suffixes indicating shaft length (S/L/XL) and control type (tiller/remote).
Confirm it’s a 4‑stroke: look for an engine oil fill cap/dipstick and an external spin‑on oil filter. Older 2‑strokes lack these features.
If ordering gearcase or prop parts, note whether you have the standard gearcase or Command Thrust/BigFoot variant.

Engine Overview

Inline‑4 EFI 4‑Stroke (60 HP class)

Feature	Description
Configuration	Inline‑4 4‑stroke with electronic fuel injection (EFI).
Common Models	Mercury 60 EFI FourStroke; variations include Command Thrust/BigFoot gearcase options.
Advantages	Smooth, quiet operation; good fuel economy; reliable cold starts and strong mid‑range torque.
Notes	Many service items cross over with 40/50/60 EFI inline‑4 models. Verify gearcase type and serial number when selecting water pump kits and propellers.

Routine Maintenance & Service Parts

Intervals below are general guidelines for typical use. Always follow the official service manual for your exact model, environment, and duty cycle.

Item	Interval*	Remarks	Parts Link
Engine oil & oil filter	Every 100 hours or annually	Use FC‑W marine oil; replace spin‑on filter with each oil change.	Oil Filters
Gear oil (lower unit)	Every 100 hours or annually	Inspect for water intrusion/metal on magnet; replace seals if contamination is found.	Mercury Lower Unit Seal Kits
Spark plugs	Inspect 100 hours; replace 300 hours or 3 seasons	Check gap and condition; replace sooner if misfire or fouling occurs.	Spark Plugs
Fuel filter / water separator	Inspect 50–100 hours; replace annually	Ethanol fuel or storage may require more frequent changes.	Fuel Filters
Water pump impeller/kit	Every 2 seasons or ~200 hours	Sand/silt use, low stream, or overheat history warrant earlier service.	Mercury Water Pump Repair Kits
Anodes (internal & external)	Inspect every 50 hours; replace when 50% eroded	Choose alloy matched to water type (salt/brackish/fresh) and keep bonding clean.	Anodes

Frequently Used Parts Categories

Routine Service: Service & Maintenance Kits
Cooling System: Mercury Water Pump Repair Kits
Fuel System: Fuel Filters
Ignition / Electrical: Electrical Items
Propulsion: Propellers
Gearcase Seals: Mercury Lower Unit Seal Kits
Corrosion Protection: Anodes

Common Symptoms & Quick Checks

Symptom	Check First	Related Parts
Weak telltale or overheat alarm	Clear intake screens; inspect impeller/housing and thermostat; check for kinked hoses.	Water pump kit, thermostat, anodes
Poor acceleration or power loss	Check prop damage/cavitation, fuel quality, fuel filter restriction, and spark plug condition.	Propeller, fuel filter, spark plugs
Hard starting or rough idle	Verify battery health and connections; prime bulb; inspect for vacuum leaks; consider IAC cleaning.	Spark plugs, fuel filter, electrical items
Gearcase noise or metal in gear oil	Check gear lube level; look for milky oil; inspect propshaft for fishing line; pressure test for seal leaks.	Lower unit seal kit, bearings, propeller hub
No charging or high voltage spikes	Measure battery voltage at idle and 2–3k RPM; inspect rectifier/regulator connectors and grounds.	Rectifier/regulator, electrical items

FAQs

Are parts interchangeable across 40/50/60 EFI 4‑cylinder models?

Many routine service parts (impellers, filters, anodes) are shared across the inline‑4 EFI family. However, gearcase components, propellers, and some cooling or fuel parts can vary. Confirm by serial number and whether you have the standard or Command Thrust/BigFoot gearcase.

When should I replace the water pump impeller?

As a preventive measure, replace the impeller about every 2 seasons or ~200 hours. Engines used in sandy, silty, or shallow water may require annual service.

How often should I change gear oil in the lower unit?

Change gear oil every 100 hours or annually. If you see milky oil, metal flakes, or water intrusion, service seals and re‑test before further use.

What information helps confirm part compatibility?

Provide the exact model name, serial number, shaft length (S/L/XL), control type (tiller/remote), and gearcase type (standard or Command Thrust/BigFoot). Photos of the nameplate and the part you’re replacing are also helpful.

Ready to find parts by horsepower, year, and model? Browse the main Mercury collection to get started.

Shop Mercury Outboard Parts

If you’re unsure about your model, send us a clear photo of the nameplate and the part you need and we’ll help verify compatibility.