Sea Sierra 2-Stroke 55HP Outboard Engine Parts

(1 products)

This page focuses on Yamaha 2‑Stroke 55HP outboard engines and helps you quickly find compatible parts and service information. Below youll find maintenance tips, common replacement parts, and troubleshooting guidance. You can also browse the main Yamaha collection for a wider selection by horsepower, year, and model. Scroll to the bottom of this page when you9re ready to start browsing parts for this engine, and remember you can use the 8Filter & Sort9 controls on the collection page to narrow results by horsepower, year range, and part category.

Browse All Yamaha Parts

How to Identify Your 55HP Model

Nameplate location: Look for the identification/serial plate on the transom bracket or swivel bracket. It lists the model code, serial number, and often the shaft length.
Reading the code: The suffix typically indicates shaft length (S/L/XL), control type (tiller/remote), and production year or revision. Match these when selecting parts.
2-Stroke specifics: These 55HP models are carbureted and may be oil-injected or premix. Check for an oil tank and lines to determine your lubrication system.
Related families: Many 55HP components are shared with certain 48HP models. Use horsepower and year filters to confirm cross-compatibility before ordering.

Platform Overview

Yamaha 55HP 2-Stroke

Feature	Description
Configuration	Inline twin, carbureted 2-stroke outboard; manual or electric start; tiller or remote control depending on model.
Common Models	55HP 2-stroke variants often grouped with 48HP models; short (S) and long (L) shaft versions. Use model plate details to confirm.
Advantages	Light weight, strong hole-shot, simple maintenance, broad parts availability.
Notes	Some gaskets, water pump components, and lower-unit parts interchange with nearby HP ranges (e.g., certain 48HP units). Always verify by HP, year, and model code using the Filter & Sort tools.

Routine Maintenance & Service Parts

Intervals below are general guidelines for typical recreational use. Always follow the official service manual and adjust for severe duty or saltwater operation.

Item	Interval*	Remarks	Parts Link
Gear oil (lower unit)	Every 100 hours or annually	Inspect for water contamination (milky oil); replace seals if needed.	Yamaha Lower Unit Seal Kits
Spark plugs	Inspect every 50 hours; replace ~100 hours	Check gap and fouling; replace sooner for heavy trolling or rich running.	Spark plug
Fuel filter / inline filter	Inspect every 50 hours; replace 100 hours	Drain water, replace if restricted; add water-separating filter if needed.	Fuel Filters
Water pump impeller/kit	Every 100 hours or 13 seasons	Replace sooner if weak tell-tale or any overheat event.	Yamaha Water Pump Repair Kits
Anodes (internal & external)	Inspect every trip; replace at ~50% depletion	Use the correct alloy for your water (zinc, aluminum, or magnesium).	Yamaha Anodes
Thermostat	Inspect annually; replace as needed	If running too cool or hot, verify thermostat condition and sealing.	Yamaha Outboard Parts
2-stroke oil system	Seasonally	For oil-injected models: check pump calibration, remote tank filter, and oil lines; for premix, use the correct fuel/oil ratio.	Hoses

Frequently Used Parts Categories

Routine Service 3 Yamaha Service & Maintenance Kits
Cooling System 3 Yamaha Water Pump Repair Kits
Fuel System 3 Fuel Filters
Ignition / Electrical 3 Yamaha Starters
Gaskets & Sealing 3 Yamaha Gaskets
Corrosion Protection 3 Yamaha Anodes
Gearcase & Seals 3 Yamaha Lower Unit Seal Kits

Common Symptoms & Quick Checks

Symptom	Check First	Related Parts
Weak tell-tale or overheat alarm	Inspect intake screens, flush for debris/sand, verify impeller and thermostat operation.	Water pump repair kit, thermostat, intake screen/gasket.
Poor acceleration or power loss	Check prop damage/cavitation, fuel restriction, carburetor cleanliness, and spark quality.	Fuel filter, carburetor gaskets/repair kit, spark plugs, prop hardware.
Hard starting / rough idle	Verify primer bulb and fuel lines, choke/enrichment function, plug condition and gap.	Spark plugs, fuel lines/hoses, carburetor kit.
Excessive smoke (2-stroke)	Confirm correct fuel/oil ratio or oil pump setting; look for stuck choke and low operating temperature.	Spark plugs, carburetor parts, thermostat, oil system hoses.
Gearcase noise or metal in gear oil	Check oil level/condition; test for water intrusion; inspect prop shaft seals and bearings.	Lower unit seal kit, bearings, shims, gear oil.

FAQs

Are parts interchangeable between different 55HP years or with 48HP models?

Some items (gaskets, cooling, and gearcase components) may interchange across certain years and with related 48HP models, but not all. Use the horsepower, year, and model code filters to confirm exact fitment before ordering.

When should I replace the water pump impeller?

For most recreational use, replace the impeller every 100 hours or every 13 seasons. Replace immediately after any overheat, sand ingestion, or weak tell-tale stream.

How often should I change lower unit gear oil?

Change gear oil every 100 hours or annually. If you find milky oil or metal particles, stop using the motor and service seals or gears before further operation.

What information do you need to confirm part compatibility?

Provide the model code, serial number, shaft length (S/L/XL), control type (tiller/remote), and year if known. A photo of the nameplate and the part needing replacement helps ensure a precise match.

Ready to find parts for your Yamaha 2-Stroke 55HP? Browse the main Yamaha collection and use the filters by horsepower, year, and model.

Shop Yamaha Outboard Parts

If you9re unsure about your model, send us a photo of the nameplate and the part you need and well help verify compatibility.