Yamaha 140HP 4-Stroke Outboard Engine Parts

(15 products)

This page is for Yamaha 4-Stroke 140HP outboard engines. Use it to find compatible parts and service information, including maintenance tips, common replacement parts, and troubleshooting guidance. You can also browse our main Yamaha outboard collection. Scroll to the bottom of this page to start browsing parts for this engine, and on the collection page use the Filter & Sort controls to narrow results by horsepower, year range, and part category/section.

Browse All Yamaha Parts

How to Identify Your 140HP Model

Nameplate location: Look for the model/serial plate on the transom bracket or swivel bracket (starboard side on most Yamaha outboards).
Reading the code: Yamaha 4‑stroke models typically start with “F”. Suffix letters/numbers indicate shaft length (L/XL), control type, and market/year code.
Confirm the platform: This page focuses on 4‑stroke 140HP models (often inline‑4). If your 140 is an older 2‑stroke V4, use the collection filters to locate the correct 2‑stroke section.
Measure shaft length: Center of mounting bracket to anti‑ventilation plate. Matching L/XL shaft length ensures correct lower unit and prop fitment.

Engine Overview

Inline‑4 4‑Stroke Platform (Typical)

Feature	Description
Configuration	Inline‑4, 4‑stroke, EFI fuel injection (typical for modern 140HP class), remote or tiller control depending on model suffix.
Common Models	140HP 4‑stroke variants with F‑prefix model codes; L/XL shaft options and different control harness configurations.
Advantages	Smooth running, good mid‑range torque, fuel efficiency, and strong corrosion‑resistance options for saltwater use.
Notes	Impellers, anodes, and gearcase seals are model‑year and shaft‑length sensitive. Verify your exact model code and serial before ordering.

Routine Maintenance & Service Parts

Intervals below are general guidelines; always follow your Yamaha service manual for the precise schedule for your engine and operating conditions.

Item	Interval*	Remarks	Parts Link
Engine oil + filter	First 20 hrs, then every 100 hrs or annually	Use NMMA FC‑W oil; replace crush washer; verify level after warm‑up.	Yamaha Service & Maintenance Kits
Gear oil (lower unit)	Every 100 hrs or annually	Inspect for water intrusion/metal; replace drain screw gaskets.	Yamaha Lower Unit Seal Kits
Spark plugs	Inspect 100 hrs; replace ~300 hrs or 3 years	Check gap and coil boots; replace sooner if misfire or fouling.	Spark Plugs
Fuel filter / water separator	Every 100 hrs or annually	Replace more often with ethanol or dirty fuel; purge water bowl.	Fuel Filters
Water pump impeller/kit	Inspect annually; replace ~2–3 seasons	Replace sooner after overheat, sand/mud use, or weak tell‑tale.	Yamaha Water Pump Repair Kits
Anodes (zinc/aluminum/magnesium)	Inspect every 50 hrs; replace when ~50% gone	Match anode alloy to water type (salt/brackish/fresh).	Yamaha Anodes
Thermostat inspection	Every 2–3 years	Replace if sticking or if overheat occurs at idle.	Yamaha Outboard Parts

Frequently Used Parts Categories

Routine Service Kits – Yamaha Service & Maintenance Kits
Cooling System – Yamaha Water Pump Repair Kits
Propellers & Hubs – Yamaha Propellers
Corrosion Protection – Yamaha Anodes
Ignition & Starting – Yamaha Starters
Fuel System – Fuel Filters and Fuel Pumps
Lower Unit & Seals – Yamaha Lower Unit Seal Kits

Common Symptoms & Quick Checks

Symptom	Check First	Related Parts
Weak tell‑tale stream or overheat alarm	Inspect intake screens for debris, verify water pump condition, check thermostat for sticking.	Water pump repair kit, intake screen, thermostat, gaskets
Poor acceleration or power loss	Confirm prop condition and pitch, replace fuel filter, inspect spark plugs, verify clean fuel.	Propeller, fuel filter, spark plugs, fuel pump
Hard starting or rough idle	Check battery charge and connections, prime fuel system, inspect plugs and air leaks in fuel lines.	Spark plugs, fuel filter, starter motor, fuel line/primer bulb
Gearcase noise or metal in gear oil	Drain and inspect oil, check for water intrusion, verify prop shaft seal area for fishing line.	Gear oil, drain screw gaskets, gearcase seal kit, bearings

FAQs

Are parts interchangeable between different years or platforms?

Some service items cross over within the same 4‑stroke platform and generation, but many parts are year, shaft length, and model‑specific. Verify your full model code and serial before ordering.

When should the water pump impeller be replaced?

Inspect annually and replace about every 2–3 seasons (or sooner after an overheat, sand/mud use, or weak tell‑tale). Full kits are recommended when service history is unknown.

How often should I change the lower unit gear oil?

Typically every 100 hours or annually. Always replace the drain/fill screw gaskets and inspect the oil for water or metal particles.

What information helps confirm part compatibility?

Provide the model code, serial number, shaft length (L/XL), control type (remote/tiller), and the part location or diagram reference when available.

Ready to find parts? Browse the main Yamaha outboard collection and filter by horsepower, year, and model to locate compatible components.

Shop Yamaha Outboard Parts

If you’re unsure about your model, send us a photo of the nameplate and the part you need and we’ll help verify compatibility.