Yamaha Outboard 4-Stroke 75-100HP Engine Parts

(7 products)

This page is tailored for Yamaha 4-Stroke 75–100HP outboard engines. Use it to find compatible parts and service information, including maintenance tips, common replacement parts, and troubleshooting guidance. You can also browse the main Yamaha collection. Scroll to the bottom of the page to start browsing parts for this engine, and on the collection page use the Filter & Sort controls to narrow results by horsepower, year range, and part category.

Browse All Yamaha Parts

How to Identify Your 75–100HP Model

Nameplate location: Look on the port-side transom bracket or swivel bracket for the model and serial number sticker.
Reading the code: Yamaha 4-stroke model codes typically begin with an “F” (e.g., F75, F90, F100), followed by letters for shaft length (S/L/X), steering/controls, and a year/series suffix.
Platform hints: 75–100HP 4-strokes are usually inline-4 engines. Depending on year, engines may be carbureted or EFI; verify fuel system type when selecting parts.
Confirm before ordering: Match horsepower, shaft length, and full model code against the parts listing to ensure proper fit.

Platform Overview

Yamaha F75/F80/F90/F100 4‑Stroke

Feature	Description
Configuration	Inline‑4 4‑stroke, typically 1.5–1.8L, carbureted or EFI depending on year/series.
Common Models	F75, F80, F90, F100.
Advantages	Smooth, quiet operation; good fuel economy; broad parts availability; durable mid‑range torque.
Notes	Many service parts (water pump kits, anodes, some filters) cross over among F75/F80/F90/F100. Verify by full model and serial; later series may use updated filters, sensors, and thermostats.

Routine Maintenance & Service Parts

Intervals below are general guidelines for Yamaha 4‑stroke mid‑range outboards. Always follow the schedule and specifications in your official service manual.

Item	Interval*	Remarks	Parts Link
Engine oil & filter	Every 100 hours or annually	Warm engine before drain; replace crush washer; use NMMA FC‑W oil.	Yamaha Service & Maintenance Kits
Gear oil (lower unit)	Every 100 hours or annually	Inspect for water intrusion (milky oil) and metal on magnet; replace seals if needed.	Yamaha Lower Unit Seal Kits
Spark plugs	Inspect 100 hours; replace 200 hours/2 seasons	Check gap and insulator color; replace if fouled or worn.	Spark Plugs
Fuel filter / water separator	Inspect every 50 hours; replace 100 hours	Drain water; replace more often with ethanol fuel or contamination.	Fuel Filters
Water pump impeller/kit	Every 200 hours or 2–3 seasons	Replace sooner for weak tell‑tale, overheat alarms, or sandy/silty use.	Yamaha Water Pump Repair Kits
Anodes (internal & external)	Inspect every 50 hours; replace when 50% depleted	Use the correct alloy for your water (fresh, brackish, or salt).	Yamaha Anodes

*Intervals are typical for many Yamaha 4‑stroke models; always defer to your exact model’s service manual.

Frequently Used Parts Categories

Routine Service Kits — Yamaha Service & Maintenance Kits
Cooling System — Yamaha Water Pump Repair Kits
Fuel System — Fuel Filters
Ignition — Spark Plugs
Starting & Charging — Yamaha Starters
Corrosion Protection — Yamaha Anodes
Propulsion — Yamaha Propellers

Common Symptoms & Quick Checks

Symptom	Check First	Related Parts
Weak tell‑tale stream or overheat alarm	Inspect intake screens, tell‑tale hose for debris, thermostat operation, and impeller wear.	Water pump repair kit, thermostat, intake screen, gaskets
Poor acceleration or power loss	Check prop damage/slip, fuel quality, clogged fuel filters, and fouled spark plugs.	Propeller, fuel filter, spark plugs, fuel pump
Hard starting or rough idle	Verify battery condition, primer bulb firmness, vacuum leaks, and injector/idle circuits.	Spark plugs, primer bulb, fuel filter, injectors
Gearcase noise or metal in gear oil	Inspect drained oil for water/metal, check prop shaft for fishing line, and seals/bearings.	Lower unit seal kit, bearings, prop shaft seals

FAQs

Are parts interchangeable between different years or platforms?

Many service items cross over among F75/F80/F90/F100 models, but filters, sensors, and some cooling/fuel components can vary by year and sub‑series. Always verify by full model code and serial number.

When should I replace the water pump impeller?

As a rule of thumb, replace every 200 hours or 2–3 seasons, and sooner if you notice a weak tell‑tale, overheat alarms, or frequent operation in sandy or silty water.

How often should I change the lower unit gear oil?

Change every 100 hours or annually. During service, check for milky oil (water intrusion) and metal shavings on the drain plug magnet.

What information do I need to confirm part compatibility?

Provide the full model code (e.g., F75/F90), serial number, shaft length, control/steering type, and the specific part or system you’re servicing. Clear photos of the nameplate and the part area also help.

Ready to find parts by horsepower, year, and model? Browse our main Yamaha collection to dial in the exact components for your outboard.

Shop Yamaha Outboard Parts

If you’re unsure about your model, send us a photo of the nameplate and the part you need and we’ll help verify compatibility.