Power Trim & Tilt Switch for Suzuki Outboards DF8–DF250 (Replaces 37850-93J10)

Product Details

This Power Trim & Tilt Switch is a replacement switch for Suzuki outboard applications from DF8 through DF250. It is intended to provide trim and tilt control when the original switch is worn, damaged, or no longer operating correctly.

The switch is identified as a replacement for Suzuki part number 37850-93J10. Before ordering, compare the original switch, connector, mounting arrangement, and control-box configuration with the product images and the information below.

• Power trim and tilt switch for Suzuki outboard applications
• Fitment range listed by the manufacturer: Suzuki DF8–DF250
• Replacement reference: Suzuki 37850-93J10
• Single switch supplied; this is not a multi-part kit

Part Number Matrix

Use the following reference to compare the replacement switch with your original part.

Engine & Model Compatibility

The manufacturer lists this switch for Suzuki outboards DF8–DF250. The exact model, year, serial number, control-box type, and switch configuration can affect fitment, so verify the original part and installation details before purchase.

Technical Specs

Product Type

Power trim and tilt switch

Application

Suzuki outboard trim and tilt control

Listed Fitment

Suzuki outboards DF8–DF250

Replacement Reference

37850-93J10

Product Configuration

Single replacement switch, not a kit

What's in the Box

• 1 × Power trim and tilt switch

Installation Notes

1. Disconnect the battery and make sure the ignition and all electrical systems are switched off before beginning work.
2. Locate the existing trim and tilt switch on the Suzuki control assembly.
3. Document the original wire positions and connector orientation before disconnecting the old switch.
4. Disconnect the wiring from the original switch and remove its mounting screws or fasteners.
5. Compare the replacement switch with the original, including the connector, terminals, mounting points, and switch orientation.
6. Install the replacement switch using the original mounting hardware where applicable.
7. Reconnect the wiring in the same configuration as the original switch.
8. Reconnect the battery and test trim and tilt operation in both directions while the boat is secured and the propeller area is clear.

Installation should be performed by a qualified marine technician if the wiring, connector, or control-box configuration does not clearly match the original component.

Troubleshooting & FAQ

What part does this switch replace?

This switch is listed as a replacement for Suzuki part number 37850-93J10. Confirm the number and physical configuration on your original switch before ordering.

Which Suzuki outboards are listed as compatible?

The manufacturer lists the switch for Suzuki outboards from DF8 through DF250. Exact fitment may depend on the engine model, year, serial range, control-box type, connector, and mounting arrangement.

Is this a complete trim and tilt system?

No. This listing is for one power trim and tilt switch only. It does not include a trim motor, hydraulic components, remote control box, wiring harness, or other control-box parts unless specifically shown with the product.

How do I know if my switch needs replacing?

Common symptoms of a failed switch include no response when the trim or tilt control is pressed, intermittent operation, or visible damage. Check the battery, fuse, wiring, connector, relay, and trim motor before replacing the switch because other electrical faults can produce similar symptoms.

Can I install the switch myself?

Installation may be straightforward for someone familiar with marine electrical components. Disconnect the battery first and record the original wiring before removal. Professional installation is recommended if you are not comfortable working on outboard control wiring.

Will it fit every Suzuki DF8–DF250 application?

The listed manufacturer fitment is Suzuki DF8–DF250, but model-specific configurations can vary. Compare the original switch, connector, mounting points, and control-box arrangement before purchase rather than relying on horsepower alone.

Safety & Important Information

• Disconnect the battery before removing or connecting the switch.
• Verify the original part number and physical configuration before ordering.
• Keep model, year, serial number, and control-box details together when confirming fitment.
• Do not operate the boat if trim or tilt controls work intermittently or unexpectedly.
• This listing includes one replacement switch only; additional control-box or engine components are not included.

About Sea Sierra

• We provide replacement marine parts for repair and maintenance applications.
• Product fitment should be confirmed against the original component before installation.
• For installation questions, provide the engine model and photos of the original switch and connector when contacting support.